找回密码
 注册

QQ登录

只需一步,快速开始

搜索
查看: 1094|回复: 2

复材1米的TS DLG组装说明

[复制链接]
发表于 2017-4-13 17:42:52 | 显示全部楼层 |阅读模式
本帖最后由 dlm718 于 2017-4-13 17:45 编辑

之前玩过的一款DLG滑翔机,看有朋友在玩这个滑翔机,在此开贴发组装教程,希望能帮到大家,这个教程是翼展1米的2通滑翔机
阿里旺旺图片20170119110014.jpg
Thank you for selecting our Mini Dlg(ARF/PNP).This dlg(ARF/PNP) is designed to be fun to fly and uses top quality material parts for durability and good performance.This instruction menual is designed to be easy and funny for you to install this Dlg.
Now lets start our happy Journey.
Features
its a all new to you.there are some features on this Mini Dlg
1. Super light Kevlar&carbon fiber covered wing,lighter and stronger .
2. New Rohacell core covered Carbon Fiber Tissue/Veil tails groups, reinforce with carbon, lighter and stronger.
3. Most of the parts were jioned or install in factory,save your time and fast to enjoy flying.
4. fully accessories support.
5. Super light dlg easy to pick up,you can fly anywhere you want.
Overview
Open your pacakge and you will see following:
1. One piece jioned wing.
2. One fuselage with boom and vertical tail installed.
3. One Horizontal tail.
阿里旺旺图片20170413173022.jpg
4. Complete accessories
阿里旺旺图片20170413173049.jpg
5. You will prepare:
2 micro servos, a battery, a receiver, a transfer, and tools needed.
阿里旺旺图片20170413173107.jpg
2 Start up guide
2.1 Wing install
Before installing,turn on your transfer,and connect all your servos with the receiver and battery.Adjust your transfer let the servo stand in the centre point.
Screw the 2 nylon screws, jion the wing with the fuselage togther.
阿里旺旺图片20170413173123.jpg
Stick the Horizontal tail to the tails boom(the slot for jioning Horizontal tail is ready)
阿里旺旺图片20170413173137.jpg
阿里旺旺图片20170413173151.jpg
Then check the situation shown in the picture.
阿里旺旺图片20170413173206.jpg
Install 2 servos to the jig
阿里旺旺图片20170413173228.jpg
Put them into the fuselage.then bond the jig to the fuselage
阿里旺旺图片20170413173243.jpg
Cut 2 1.5 cm tube ,and heat it. Put the tube through the wood block,then stick it to the pod with CA.
阿里旺旺图片20170413173300.jpg
阿里旺旺图片20170413173314.jpg
阿里旺旺图片20170413173327.jpg
Let the push rods through the fuselage,then through the tube pass them.
Bond the
阿里旺旺图片20170413173339.jpg
Bond the wood block to the servos jig,screw the screws.
阿里旺旺图片20170413173353.jpg
Cut 5 segments heat shrink tubes,
阿里旺旺图片20170413173404.jpg
Heat them then bond them to the boom.
阿里旺旺图片20170413173416.jpg
Cut a piece of balsa wood then bond it to the boom too.bend the end of push rod to ‘Z’
阿里旺旺图片20170413173429.jpg
阿里旺旺图片20170413173446.jpg
Sand the following parts shown in the picture.
阿里旺旺图片20170413173456.jpg
Bond the carbon sheet for the peg reinforcement
阿里旺旺图片20170413173508.jpg
Bond the launching peg
阿里旺旺图片20170413173518.jpg
Launching peg situation
阿里旺旺图片20170413173530.jpg
install the battery,receiver,and connect the servos to the receiver.
Check the CG.(CG is about 54mm~58mm from the leading edge)
阿里旺旺图片20170413173545.jpg
阿里旺旺图片20170413173001.jpg

点评

海!外直播 t.cn/RxBC0cw 禁闻视频 t.cn/RxkPOKC 国际上完全孤立,臭名昭著;国内贪官横行,流氓成性;富人恐惧,争相移民;文人折腰,见风使舵;只剩互联网上那仅存的一丝火焰,为未来,为后代,在顽强的呐喊..  发表于 2017-4-15 10:30
 楼主| 发表于 2017-4-13 17:48:02 | 显示全部楼层
这个滑翔机小巧便携,现在又是春暖花开的时间,正是好玩的时候
我这里还有1.5米的,2米的及其他款式滑翔机的组装说明,后面大家有需要,我再开贴上教程
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

Archiver|手机版|小黑屋|     repair

GMT+8, 2018-8-15 22:24

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回复 返回顶部 返回列表